• Need to stream your camera from a remote location? You can capture and stream your IP camera remotely over the internet by setting up external remote access.
• The idea of drilling holes through the walls of your house to run video and power cables for a.
• An IP Security Camera uses digital rather than analog video transmission (IP Security Cameras transmit video and power from CAT-5 cable rather than separate RG59 and.

Configure Easy. N IP Web Camera. Call me paranoid but I love to have a way to check my house is ok when I’m away. The obvious choice is a webcam and the requirements I had were: Wireless: I wanted to be able to put it anywhere in the house. Night vision: Most burglars aren’t polite enough to wait for daylight. Motion sensor: If someone breaks in I want to know immediately. Cost- effective: i.

IP Camera User Manual. The HH9000 Series of video cameras are intended for network video surveillance applications. The H.264 video compression algorithm.

Despite some poor reviews on Amazon. I felt I would be OK at configuring it. Install Flash Plugin In Debian Screenshots. As it turned out it was a bit of a fiddle so I can understand why some people had trouble. I think if you set it to use a fixed IP it uses the same MAC on both. However I set the camera to DHCP so as to only be setting the IP in one place (the router) and to avoid potential conflicts with other devices.

Configuration. Part 1: Check the Subnet. The subnet is the first three parts of your computer’s IP address. This camera comes configured with an IP of 1.

LAN/router is configured say for a 1. If you are on a 1. Tell if you are on a 1.

Tips on how to connect your DVR over the internet. Connecting your DVR over the internet gives you many advantages, read this article and get to know them. Contact us.

Subnet. In Windows: click Start and type cmd. At the prompt typeipconfig. Press return and you’ll see results like below: Wireless LAN adapter Wireless Network Connection: Connection- specific DNS Suffix  . If you don’t know what DHCP is don’t worry. Part 2: Configure the Camera. If you are on a 1.

You should see the Easy. N web interface: Click the Options on bottom right to open the Configuration interface: Set a Password. If you are going to expose the camera on the web you should set a user and password other than the default in: Settings; User Settings. Setup the Wireless. Aoe Rise Of Rome Cd Cracks.

In the Configuration Interface: Click “Wireless Lan Settings”Click “Scan'” and select the relevant Wireless SSID (name). Enter the Shared key in the box marked “Share Key”. Click “Set”. The resolution they came up with was to grab the form post data and manually URLencode the problem characters then manually submit the resulting URL which worked for them. To quote. . The final URL for a WPA2 PSK with AES encryption (had to escape #, % and +). To set the default angle: Go into the web interface (http: //1.

Adjust the camera viewing angle to the desired position. Click . 9 is left of centre, 1. Click Options; PTZ Settings and in “Started running to the specified preset” chose the number assigned above. Optionally you can set the rotational speed.

Light display Mode. I found the flashing LED quite annoying. This can be turned off at: Options; PTZ Settings; Indicator Display Mode; Been extinguished. I would have liked it to blink when it .

Click Test to ensure they work before setting. For GMail I used: SMTP: imap.

Transport Layer Security Protocol: STARTTLSNeed Authentication: Yes. User and Password. I also clicked “Report IP by Mail”Motion Detection. I found the default settings for motion detection were too sensitive and it was emailing me all the time with blank pictures.

Change this in Settings; Alarm Service Settings. I used: Motion Detect Armed: Yes. Motion Detection Sensibility: 3.

Start the motion detection compensation: Yes. Send Mail on Alarm: Yes. I also use the scheduler which to be honest is a pain to setup: rather like minesweeper, but less exciting. The logic being I can turn off the scheduler when I’m away (remotely if I forget before I go). Access the Camera remotely: DNS Update. Unless you have a static IP which is unlikely, to access your camera from the internet remotely you will need a dynamic IP updater service as your public (WAN) IP will change periodically. This will run on your system locally and update a DNS record on the chosen service provider with your public IP.

You can check your public IP by doing a search on- line for . NB: You should NOT configure it on both the router and the camera. I would recommend you do it on your router: If I configure it on the camera I get: ”Errors in Network Communication”I suspect this is either because the camera is unable to contact the DNS service or is reporting it’s LAN IP address (rather than it’s WAN IP).

However, to do it on the camera: Go to the camera's setup and select DDNS Service Settings. Select the service provider from the list. Enter the username password and host details. You will need to enable the port on your router (usually under Port Forwarding). The default is 8. Depending on your router you may need to forward it to the camera's local IP (default 1.